Topends

Inlet assembly weld failures

The standard adopted for the examination of Reformer Tubes in Steam Methane Reformers (SMR) has been to inspect the heated length of the tube within the furnace. The portion of the tube outside of the heated length is normally not inspected after being in service. However, recent trends have changed that perspective due to internal defects encountered in these portions of the top ends. These defects have been found in two completely different design arrangements which will be described separately as Case I and Case II.

Inspection of Topends (EN)

Case I - Top Fired / Down Flow:

In these reformer designs, the burners are top fi red with a down flow process. The inlet gas is injected through a pigtail into the tube above the furnace radiant box in the penthouse. The unheated tube top section is made of wrought material with metallurgies ranging from low-chrome alloy steel (1.25 Cr - 0.5 Mo) to stainless steel 304H, 347H, or similar materials while the heated length within the furnace is a centrifugally cast material mostly 25Cr/35Ni/Nb or with Micro-alloy additions. For further details see Figure 1.

During transient and cold weather conditions, the temperature of the tube top flange can drop below the process gas dew point resulting in condensation in the area shown in “black”. The process gas dew point is typically in a range of around 300-400 °F.

Case II - Bottom Fired / Up Flow:

In these reformer designs, the reformer is bottom fi red with an up-fl ow process. The inlet gas is injected from the bottom of the tube through an inlet pigtail and the reformed gas comes out from the top of the tube through an outlet pigtail. The outlet pigtail is located on the portion of the tube outside of the heated length on an uncovered roof open to the atmosphere. The tube material is made of the same material as the heated length which is centrifugally cast length which is a centrifugally cast material mostly 25Cr/35Ni/Nb or with Micro-alloy additions. In this scenario, the process gas can also reach its dew point around 300-400 °F and cause “condensation”. See Figure 2.

The cyclic stresses brought on by these variations in temperature result in the damage mechanism as “thermal fatigue”. In both Case I and Case II, the defects manifest themselves in the form of circumferential cracks or pinhole cracks that initiate from the ID and propagate towards the OD resulting in a leak.

Typical Moderate Crack Signal

Top End Ultrasonic Inspection

Inlet Assembly Weld Failures

Several furnace designs utilize a dissimilar weld to connect the inlet assembly to the reformer tube. In some cases, this has led to cracking in the heat affected zone of the weld on the lower alloy side. MP has developed a customized testing device and procedure for testing these welds in some furnaces.

Procedures can be adapted for many furnace designs. This is an ultrasonic test incorporating special devices to assure complete coupling and accurate probe manipulation from the ID. Cracks are detected and sized allowing the continued safe operation of the furnace.

This website uses cookies

We use cookies to personalize content and advertisements, to be able to offer functions for social media and to analyze access to our website. We also share information about your use of our website with our social media, advertising and analytics partners. Our partners may combine this information with other data that you have provided to them or that they have collected as part of your use of the services.

Our cookies have changed, so you will need to give your consent again.

Your previous consent to our cookies has expired, so you will need to consent again.

Necessary cookies help to make the website usable for the user. They store basic information, such as a login to the website or the consent to the individual cookies.

Name Provider Purpose Duration Type
__hs_opt_out HubSpot notwendig

This cookie is used by HubSpot to ensure that a user after an opt-out does not have to ask for consent again.

13 months Cookie
__hs_do_not_track HubSpot notwendig

This cookie is used by HubSpot to disable the tracking of a user.

13 months Cookie
__hs_initial_opt_in HubSpot notwendig

This cookie is used by HubSpot to store the consent to tracking.

7 days Cookie
hs_ab_test HubSpot notwendig

This cookie is used by HubSpot to always assign a user to the same group during A/B tests.

Session Cookie
*_key HubSpot notwendig

This cookie is used by HubSpot to prevent a user from having to log in multiple times for the same content.

14 days Cookie
hs-messages-is-open HubSpot notwendig

This cookie is used by HubSpot to save chat widget settings.

30 minutes Cookie
hs-messages-hide-welcome-message HubSpot notwendig

This cookie is used by HubSpot to ensure that the welcome message of the chat is displayed once a day.

1 day Cookie
__hsmem HubSpot notwendig

This cookie is used by HubSpot to store the login process of a user.

1 year Cookie
hs-membership-csrf HubSpot notwendig

This cookie is used by HubSpot to prevent a login process from being corrupted.

Session Cookie
hs_langswitcher_choice HubSpot notwendig

This cookie is used by HubSpot to store the language selected by the user.

2 years Cookie
__cfduid HubSpot notwendig

This cookie is used by HubSpot to securely transfer data via CDN / Cloudfare.

Session / 30 days Cookie
__cfruid HubSpot notwendig

This cookie is used by HubSpot to securely transfer data via CDN / Cloudfare.

Session Cookie
gits_cookie_accepted_* digiwerk GmbH

Saves the cookie banner selection.

unlimited LocalStorage
DataTables_* TYPO3

Is stored by the CMS system TYPO3 vebSaves user settings for displaying data in the backend.

unlimited LocalStorage
t3-tabs-* TYPO3

Saves user settings for displaying data in the backend.

unlimited LocalStorage
be_typo_user TYPO3

Required by the CMS system TYPO3 to allow users to log on to the backend.

1 year LocalStorage
PHPSESSID TYPO3

Required by the CMS system TYPO3 to allow users to log on to the backend.

1 year Cookie

Marketing cookies help to recognize visitors to websites. This enables, among other things, to show them more accurate advertisements and search results.

Name Provider Purpose Duration Type
__hstc HubSpot

This cookie is used by HubSpot to register a unique ID that can be assigned to statistical data of the user.

13 months Cookie
hubspotutk HubSpot

This cookie is used by HubSpot to register a unique ID that can be assigned to statistical data of the user.

13 months Cookie
__hssc HubSpot

This cookie is used by HubSpot to detect the session of a user.

30 minutes Cookie
__hssrc HubSpot

This cookie is used by HubSpot to detect the session of a user.

Session Cookie

Statistical cookies help to understand how visitors interact with the site by collecting and reporting information anonymously.

Name Provider Purpose Duration Type
_pk_id.*.* Matomo

This cookie is used by Matomo to store some details about the user, such as the unique visitor ID.

13 months Cookie
_pk_ses.*.* Matomo

This cookie is used by Matomo, for short-lived cookies, which are used for temporary storage of data for the visit.

30 minutes Cookie
_pk_testcookie..undefined Matomo

This cookie is used by Matomo to check whether the visitor’s browser supports cookies

Session Cookie

Cookies are small text files that are used by websites to make the user experience more efficient.According to the law, we can store cookies on your device if they are absolutely necessary for the operation of this site. We need your permission for all other types of cookies.This site uses different types of cookies. Some cookies are placed by third parties that appear on our pages.